This topic has been archived. It cannot be replied.
-
枫下家园 / 家用电器 / GAS壁炉不需要120v电源。墙上那个开关是个短路开关,连接气阀控制电路的两个触点。任何时侯壁炉都可以手动打火,再开墙上的开关,火就起来了。好些人不知道这一点,挨冻了。
-mrsub(西出阳关);
2014-1-1
(#8534984@0)
-
这个,很多型号的Gas Fireplace是有motor的,没有电是不工作的。
-bluesky2000(bluesky2000);
2014-1-1
(#8535089@0)
-
那是blower, 是个选项。不工作也没有关系。壁炉取暖主要是热辐射, 不是对流
-jinglin(精灵);
2014-1-1
(#8535120@0)
-
+10
-mrsub(西出阳关);
2014-1-2
(#8535584@0)
-
这个,连试试的勇气都没有的话,别说挨冻,生存都有问题。
-wdqin(加东);
2014-1-2
(#8535578@0)
-
清洁完成后,最容易检查的就是墙上的Switch,将盖打开,将里面的线直接短接,看看壁炉是否工作。(一定确定你的控制开关不是用120V电的,否则后果自负)
-bluesky2000(bluesky2000);
2014-1-5
(#8540505@0)
-
呵呵,都等着自由党省长发福利呢
-firetrain(火车头);
2014-1-6
(#8540592@0)
-
请问,我家的这个开关最近开始,有的时候可以点起大火,有的时候点不起来,有的时候点起大火以后,不知道什么时候,大火就自己关了. 请问这是怎么回事?(下面的小火种一直都没有问题)
-tdtq2009(tdtq);
2014-1-5
(#8539770@0)
-
我家的GAS壁炉也有同样问题, 开一会之后大火自动熄灭,小火一直在的。 有懂行的大虾知道原因吗??
-this(new day);
2014-1-5
(#8540148@0)
-
不是大虾的说,应该是燃烧反馈机制出错了,然后保护机制把gas关掉了。Gas阀门打开后,它要确定烧起来了,否则就有很大的危险。有时候是有根管一直在火里烧着,传导回阀门。要是阀门没收到,就会很快关上。
-chenmacro(逸浪);
2014-1-5
(#8540263@0)
-
今天试了家里的壁炉,有同样的问题。以前也是有时都烧着,有时就只剩小火苗了。懂行的大虾指点一下怎么回事。
-spring2006(猪猪和牛牛);
2014-1-5
(#8540276@0)
-
PowerVent壁炉,需要加电加强排烟,部件多原因复杂。一般的家用壁炉,称为Milivolt,容易出问题的部件Thermocouple-Switch-GasValve。先将壁炉简单清洁一番,检查线路连接是否松动,有没有长锈,有没有蜘蛛网堵住Gas出口,因为控制电压低,电阻过大造成壁炉不工作。
-bluesky2000(bluesky2000);
2014-1-5
(#8540501@0)
-
还有就是THermocouple,经常烟熏火燎的,最容易出问题,卸下来用砂纸打磨一下,没准就又能工作了。
-bluesky2000(bluesky2000);
2014-1-5
(#8540508@0)
-
thermopile在小火头烘烤下应产生360毫伏电压,短路开关闭合后,主煤气阀开启,生火。thermopile残旧产生电压不稳定,主煤气阀会关闭。个人认为长期开着小火头损害thermopile寿命。
-mrsub(西出阳关);
2014-1-6
(#8540927@0)
-
这个是重要生存技能,得学学。话说,没电怎么给信号?气阀他不开啊
-kafar(挨踢人士888);
2014-1-6
(#8541007@0)
-
thermopile在小火头烘烤下应产生360毫伏电压使主煤气阀开启。
-mrsub(西出阳关);
2014-1-6
(#8541119@0)
-
如果是这样,我应该一开开关就能打开气阀。可惜不行。 说明书上也写着需要120V电,貌似无解。
-kafar(挨踢人士888);
2014-1-6
(#8541144@0)
-
你说的好像有点问题:开关虽然是给出通、断信号,但控制电路没有电是不工作的,无法开启阀门。所谓360mV的感应电压太低,不可能开启阀门。
-makino(yuuki);
2014-1-6
(#8541887@0)
-
大爷,冒昧黑你一把。别想当然。不懂多问。MrSub不光吃Sub看起来还修Sub。嘿嘿。
-serviceman(专心老猫);
2014-1-7
(#8542232@0)