This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 请教高人:32层的 building,downfeeding system, mains (cold and hot water) and riser valves 均在32层,但在高峰用水期间(早7:00左右),这层(有时是整层)厨房和卫生间没有热水(或很少热水),冷水正常。2个booster pumps. PRV: 195Psi.热水为什么很少,哪去了?
-jimli6(jimli6);
2010-3-11
(#5939272@0)
-
Did you investigate the condition at the lower floors?
-rockywei(落基山);
2010-3-11
(#5939276@0)
-
Lower zone is Good. everything is OK.
-jimli6(jimli6);
2010-3-11
(#5939552@0)
-
你说的195 psi 一定有误,如何得到的数据? 一共32层,会有多个循环,每个循环上都有平衡阀。我觉得是平衡阀的问题。
-newsunnyhome(佳家);
2010-3-11
(#5939364@0)
-
195 psi是压力表显示的,位于booster pump PRV附近。这个building有二个区,upper zone and lower zone。你说的循环指的是什么?
-jimli6(jimli6);
2010-3-11
(#5939566@0)
-
我说的循环是指recircling,你说的booster就是循环泵。一般的卫生器具不能超过七八十psi,所以195psi不能直接连器具。有时每一层一个小循环,有时竖向对应的单元一个小循环。为了达到每个小循环的水量相同,每个小循环上有个平衡阀。
-newsunnyhome(佳家);
2010-3-11
(#5939793@0)
-
谢谢回复!我说的booster不是循环泵(recirc pump for hot water),而是位于P1 (Parking Level 1)的高压泵(booster pump for cold water),因为水压要逐层递减,所以在P1是195psi,到顶层锅炉间水压就减到60psi。我的问题是...我说的booster不是循环泵(recirc pump for hot water),而是位于P1 (Parking Level 1)的高压泵(booster pump for cold water),因为水压要逐层递减,所以在P1是195psi,到顶层锅炉间水压就减到60psi。经2锅炉加热后,热水经2 hot water tanks and 2 mixing valves 到hot water main.我的问题是:mains (cold and hot water) and riser valves 均在32层, 就是你说的有多个竖向对应的单元小循环,但在高峰用水期间(早7:00左右),这层(32层,有时是整层)厨房和卫生间没有热水(或很少热水),冷水正常。.热水为什么很少,哪去了?
-jimli6(jimli6);
2010-3-12
{493}
(#5941693@0)
-
mains and riser valves在32层,并不代表一定是downfeeding,有时立管先下到底层,在upfeed上来,说是利于排气。是不是这个原因呢?
-newsunnyhome(佳家);
2010-3-12
(#5941994@0)
-
同意这个说法。
另外如果每个分支有小循环的话,在MAINS处或是分支处接反供水回水,就将upfeed变成了downfeed系统了。
-bluesky2000(bluesky2000);
2010-3-12
(#5942072@0)
-
打开32层ceiling看了,确实是downfeed系统 (施工图也显示这一点),我在想是否与热水量有关呢?三年新的building,这个问题已有3,4个月了。以前为什么没这个问题呢?
-jimli6(jimli6);
2010-3-13
(#5943449@0)
-
那我真的不知道是什么原因了。如果是热水量的关系,前几年也该出现这个问题,而且问题也不该出现在整层,底层应该也该有类似情况。除了32层,其它各层都没有干管吗?
-newsunnyhome(佳家);
2010-3-13
(#5943619@0)
-
upper zone: mains (cold and hot water) and riser valves 均在32层; 但在高峰用水期间,这层(有时是整层)厨房和卫生间没有热水(或很少热水),冷水正常.
lower zone: mains (cold and hot water) and riser valves 均在19层.
-jimli6(jimli6);
2010-3-13
(#5943755@0)
-
希望现在是见证高人倾听高见的时刻!!!
-jimli6(jimli6);
2010-3-14
(#5945216@0)
-
装个高手试试吧. 是热水加热系统的自动控制起作用了. 高峰期热水用得太快, 如果还保持原有压力,可能整栋楼都没有热水了,减少压力,热水加热提速,到达一定温度后压力就恢复了. 所以你住顶楼吃了这个亏. 以前为什么没有,因为是新楼,人没有住买,现在可能基本住满了,问题就慢慢来了.
不知道是不是这个原因....... 这个高手装得像不像.
-net(net);
2010-3-14
{195}
(#5945314@0)
-
1.如果是热水量不够,不够仅限与某一小循环(32层),与此对应的就只有该小循环的相关器具,平衡阀,或该小循环的主管道.2.问题仅在高峰期出现,故与热水量相关.3基于1,2,先查平衡阀再说.
-xiaxinde(四万六万百千万买蜗居);
2010-3-15
(#5945965@0)
-
Lz说32层不是单独的小循环。
-newsunnyhome(佳家);
2010-3-15
(#5946525@0)
-
32层即不是单独的小循环,Recire管也没有平衡阀。
-jimli6(jimli6);
2010-3-15
(#5946794@0)
-
减少压力,热水加热提速。实际过程中如何操作?现在压力是:195Psi,锅炉处压力是:60psi.压力减到多少合适?如何使热水加热提速?
-jimli6(jimli6);
2010-3-15
(#5946780@0)
-
哈哈,这是锅炉专家的问题了. 通常当压力减少,水流也降低,水在锅炉中停留的时间加长,热水升温就加快. 但吃亏的是您住顶楼的朋友了. 所以此情况跟管道和阀门关系不大,找锅炉公司吧. 或许换个自动控制器就解决问题了!!!
-net(net);
2010-3-15
(#5947327@0)
-
自动控制器可以减少压力及热水加热提速?我愿意去问问。会不会是锅炉的能力不够?
-jimli6(jimli6);
2010-3-15
(#5947586@0)
-
自动控制器可以减少压力及热水加热提速?看起来是一件矛盾的事。有没听说哪家公司做这类的自动控制器呢?
-jimli6(jimli6);
2010-3-17
(#5951728@0)
-
热水采用下供时,设计时考虑同时使用系数,当低层的用户阀门全打开时,上层的用户用水量肯定不够,这是正常的现象。现在的情况要想改善,就要减少低层用户的用热水量。可以适当调高热水供水温度(在规定的范围内),通过调节MIXING VALVE应该可以实现。
-bluesky2000(bluesky2000);
2010-3-15
(#5947387@0)
-
问题是无法减少低层用户的用热水量,已调高MIXING VALVE热水供水温度,我都想关掉MIXING VALVE的冷水阀。
-jimli6(jimli6);
2010-3-15
(#5947567@0)
-
自动控制器可以减少压力及热水加热提速?看起来是一件矛盾的事。有没听说哪家公司做这类的自动控制器呢?
-jimli6(jimli6);
2010-3-18
(#5953893@0)
-
所谓自动控制器我也是第一次听说,理论上讲对提高高峰水温无任何帮助。想要提高温度,必须要提高锅炉的Recovery Rate,也就是更换大功率锅炉。不过,如果低层用户的水温全部没有问题的话,不见得百分百是锅炉的问题。另外高峰热水用水量通常在晚间,早上出现这个问题的确奇怪,觉得控制系统出状况的可能性大。不知能否把Schematic drawing给大家看看,也许有高人能帮上忙。
-newsunnyhome(佳家);
2010-3-18
{213}
(#5953920@0)
-
还有一个可能,早上洗脸刷牙冲厕所,冷水用水量大,造成热水炉供水量不足。看看是否可以调小供热水炉以外的其它冷水支管的水量,一来保证水炉供水,二来可提高混合水的温度,同时可减少低层用户的热水用量(冷水少了,热水必须同时减少,才能使出水水温不过热)。
-newsunnyhome(佳家);
2010-3-18
(#5953931@0)
-
非常感谢!水温好像问题不大,仅仅是热水量在早上很少或有时没有热水。调小供热水炉以外的其它冷水支管的水量,我可以试一试。只是都是球阀,理论上应全开或全关。另提高锅炉的Recovery Rate,是不是现在的锅炉能力不够导致热水量不足?或booster pump能力不够导致冷水量不足(以至于高峰期间锅炉冷水进水不够)?
-jimli6(jimli6);
2010-3-18
{139}
(#5953960@0)
-
我想表达的和你所说的热水量是一个意思.冷水量不只和加压泵有关,和管网的水压也有关系,周围是不是有刚入住的building?你提到的195psi和60psi是早上的数值吗?如果数值一天内很稳定,就是锅炉的问题。如果早上压力降低很多,就是冷水量的问题。即使是锅炉的问题,我提到的关小其他支管的办法,也能起到一定作用。
-newsunnyhome(佳家);
2010-3-18
{179}
(#5954001@0)
-
好像是正解。
-underwaterman(和兴);
2010-3-18
(#5954142@0)
-
什么是正解?
-jimli6(jimli6);
2010-3-28
(#5975760@0)
-
195psi和60psi是白天的数值。
-jimli6(jimli6);
2010-3-18
(#5954162@0)
-
球阀也有调节水量作用.
-newsunnyhome(佳家);
2010-3-18
(#5954048@0)
-
别忘了把低区冷水总阀关小。仔细想了一下,上诉的可能性相当大。
-newsunnyhome(佳家);
2010-3-18
(#5953961@0)
-
我的观察是二台booster pumps一直在工作。是否应再加一台在高峰时三台一起工作。
-jimli6(jimli6);
2010-3-18
(#5953965@0)
-
先观察各时段压力变化才好下结论。
-newsunnyhome(佳家);
2010-3-18
(#5954008@0)
-
上诉的可能性---不是我要考虑的。解决这个问题是我想要做的。
-jimli6(jimli6);
2010-3-21
(#5958699@0)
-
如果问题真如楼上朋友所说,你的操作恰恰反了。你应该减低热水供水温度,从而使热水量增加,顶层就会有足够的热水了。
-newsunnyhome(佳家);
2010-3-18
(#5954122@0)
-
减低热水供水温度,增加的就不是热水量了。变成温水了。
-jimli6(jimli6);
2010-3-18
(#5954155@0)
-
周围还没有有刚入住的新的building。
-jimli6(jimli6);
2010-3-19
(#5955699@0)
-
嗨!藏龙卧虎的多伦多,这个问题有那么难吗?
-jimli6(jimli6);
2010-3-23
(#5963972@0)
-
江郎才尽???
-jimli6(jimli6);
2010-3-26
(#5972139@0)
-
Is it possible to solve the problem?
-jimli6(jimli6);
2010-3-31
(#5982952@0)
-
Is it possible to solve the problem?
-jimli6(jimli6);
2010-4-1
(#5985935@0)
-
热水为什么很少,哪去了?
-jimli6(jimli6);
2010-4-4
(#5989112@0)
-
热水为什么很少,哪去了?
-jimli6(jimli6);
2010-4-9
(#6001095@0)