This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 懂暖炉技术的朋友帮帮忙。。我家去年10月底安装了高效能暖炉,但温控器与炉子配合不好,具体是当室内温度与设定温度相同时炉子每隔10分钟左右就启动3-5分钟然后停下(但此时温控器显示室温仍然与设定温度相同),就这样不断地循环。安装公司在2周内已经换了4个温控器,情况依然如旧,心情十分郁闷,请各位帮忙分析原因,先谢谢了。
-wdq2000(无边);
2010-1-20
{281}
(#5824427@0)
-
请给些建议好吗?我实在让不停地启动烦透了,费煤气不说,吵得慌!!!
-wdq2000(goodman);
2010-1-21
(#5824566@0)
-
could you tell us what type of furnace and thermostat? i think you can get more information from the manual.
-bluesky2000(bluesky2000);
2010-1-21
(#5826145@0)
-
炉子doodman 温控器honeywell
-wdq2000(goodman);
2010-1-21
(#5827039@0)
-
如果像这样就照我说的做吧。。。
-dragonlover(叶公);
2010-1-22
(#5828097@0)
-
问题是炉子在没有“温度差”的情况下不断启动,即设定温度与与室内温度相等的情况下,每隔10分钟左右就启动3-6分钟,这样不断循环。这样煤气能否省不好说,但噪音间隔短,费电是肯定的,因为风扇马达在启动时的用电量是运行时的好几倍,另外我想不断启动也会影响风扇和炉子的寿命。
-wdq2000(goodman);
2010-1-21
{205}
(#5827085@0)
-
it is hard to say the reason, maybe the thermostat's location is not correct, close to supply duct or the capacity of the furnace is too high for your house.
-bluesky2000(bluesky2000);
2010-1-21
(#5827170@0)
-
温控器的周围没有出风口,较远有一个进风口。炉子的荷载2500坪尺,我的房子只有1100坪尺。正巧我的朋友上周也装了和我相同的炉子和温控器,面积也基本相同,今天我观察了2小时,问题和我的相同。是否这样的情况算正常?有没有其他人有这样的情况,请讨论一下。
-wdq2000(goodman);
2010-1-21
{199}
(#5827212@0)
-
first check the thermostat, set the temperature higher 25 and lower 18 to see wherther the furnace works properly
-bluesky2000(bluesky2000);
2010-1-21
(#5827177@0)
-
温控器已换了4个。炉子也单独检查,说没问题。我在不同温度段也做过实验问题依旧。即我设最高21度,20.5度,19.5度,19度,最低18度,当室温高于设定温度时炉子不启动,低于时启动,一直当两者温度相等时炉子停止工作,而后炉子就在设定温度和室内温度相等的情况下不断重复启动。
-wdq2000(goodman);
2010-1-21
{168}
(#5827256@0)
-
there is no problem at all on the furnace or the control.it is simply too sensetive control. if you set 21+- 0.5, it will work better than 21+-0.1
-xiaxinde(四万六万百千万买蜗居);
2010-1-22
(#5827790@0)
-
i think your furnace is high-efficiency two stage furnace, how about your thermostat ? is two stage too? what is the model of HOneywell
-bluesky2000(bluesky2000);
2010-1-22
(#5827918@0)
-
there is something wrong with the setting of anticipator.
-bluesky2000(bluesky2000);
2010-1-22
(#5828163@0)
-
同问何因?我的旧暖炉工作循环是,工作几分钟,停20几分钟到半小时。而新换的高效炉是,工作十几分钟,只停几分钟。
-tlzn(Jack);
2010-1-21
(#5824663@0)
-
这种情况应该和温控器无关. 找个有牌的人帮你看一下。
-frankgexin(逆水行舟);
2010-1-21
(#5824704@0)
-
看来情况和我的相同,请问炉子和温控器是什么品牌?
-wdq2000(goodman);
2010-1-21
(#5827045@0)
-
Honeywell TH6000
-tlzn(Jack);
2010-1-22
(#5828022@0)
-
i check the goodman furnace manual just now,i suggest replace the filter and chech all the register and return air terminal, wheather it is obstructed or not, check the integrated control board LED, wheather give you some clue, flash. if everything is OK, so it is common. just wanna reduce the noise of the furnace, you can adjust the air flow
-bluesky2000(bluesky2000);
2010-1-22
{300}
(#5828905@0)
-
for honeywell ht6000 thermostat, you can change the setting for system 5 then change the heating cycle per hour.
-bluesky2000(bluesky2000);
2010-2-2
(#5855927@0)
-
我家的和你一样。我的原因是温控器的设定是中效炉, 改成高效炉就好了。设定开关在温控器背面。有些温控器可以改变cycle 的频率, 设定一般也在后面。
-dragonlover(叶公);
2010-1-21
(#5824822@0)
-
把furnace换回中效的或低效的试一试
-sharkbait(nemo);
2010-1-22
(#5828222@0)
-
不知问题解决没有。我家今天也装了新炉子,和你的问题差不多。设定67F,没等温控显示降到66F炉子就启动。查了温控器的说明书,有3个cycle可选择Fast 0.4F, Medium0.6F, Slow 1.8F。温控器出厂时社为Medium 0.6F。也就是说温度低于设定0.6F, 即大概0.4度炉子就会启动。我想这就是为了保持一个好的恒温吧。你要不想频繁炉子启动就设成slow cycle应该会好的..另外温控器应该和中效或高效炉无关,至少我的温控器是这样.好好读读温控器说明会有用的. 还有频繁启动也应与房子的保温有关而不仅仅是房子的大小.
-xinxin22(xinxin);
2010-1-27
{268}
(#5842743@0)
-
我有三个温控器,可是都没有找到你说的“有3个CYCLE"的调节开关,在哪里能看到?我有“HONEYWELL" 和”WHITE-RODGERS"两个牌子, 你用的是什么牌子?谢谢
-tlzn(Jack);
2010-2-1
(#5852988@0)
-
My is Rogers, but I found the SLOW cycle doesn't work. The furnace still start to run even at set temperature!
-xinxin22(xinxin);
2010-2-8
(#5869681@0)
-
当炉子oversize的时候,就会出现不断起停。你说你家才1100坪尺,有地下室吗?有Build-in车库吗?insulation好不好,窗子多不多,漏风不?这些都将影响炉子的size。然后你家炉子是多少BTU呢?
-byong(小贝壳);
2010-1-27
(#5842974@0)
-
我和你的问题相似, 也没解决问题呢.我估计赞美都是暖炉装的功率偏大, PM给你电话,说说病情.
-ingridchao(Ingrid);
2010-1-31
(#5852392@0)
-
i check the manual of thermostat, there is an item for the setting of heat cycle per hour. you can adjust and see wheather there is something defference with before.
-bluesky2000(bluesky2000);
2010-2-2
(#5855919@0)
-
给个不专业的办法。我自己家里这么弄的,用透明胶带,贴住thermalstat的通气孔。我看了它有四个通气孔,第一次贴住一个,没什么变化。再贴一个稍有加长。现在四个全贴住。前几天最冷的时候,一个循环也在25分钟左右。暖和的时候在40分钟以上。
暖炉的启动和停止是个振荡过程。暖炉启--温度升--暖炉停--温度降。你只要能降低thermalstat的敏感度,就能加长这个循环周期。
如果你的还是太短,用棉被把它捂住
-ai97(温酒吧地爱板);
2010-2-1
{364}
(#5853681@0)
-
哈哈,VERY FUNNY 。如果用棉被捂住,house岂不是变成桑拿室了?我知道你是开玩笑。不过你的土法看起来行的通,可是加热后,由于温控器不敏感了,温度是否已经远远超过了设定的温度,暖炉还在加热呢?
-tlzn(Jack);
2010-2-1
(#5854540@0)
-
不是搞暖通的,懂点电,仅供参考。通常炉子启动,一定会收到温控器的信号(可以听见继电器吸合的声音)。
1. 断开温控器,如果炉子还启动,问题一定在炉子自己启动,修炉子。
2.关于温控器太灵敏,通常温差可以选择。有些0.3度,有些0.5度,还有1度的,建议换一低灵敏度温控器或增大温差。
-5235(5235);
2010-2-1
{238}
(#5855000@0)
-
如何增大温差?我在温控器上找不到可调节温差的地方
-tlzn(Jack);
2010-2-1
(#5855137@0)
-
it is not a hard switch outside, it is a setting in the manu.
I have a 'Globe' controler, it can be set 4 stage, 0.5/1/1.5/2
-5235(5235);
2010-2-3
(#5858776@0)
-
不用太担心吧。显摆一下,俺上学的时候还试图研制恒温箱,精确到万分之几度,用铂电阻温度计,用PID控制,后来用户方觉得我们毛头小子难当大任,没把任务交给我们。遗憾啊
-ai97(温酒吧地爱板);
2010-2-1
(#5855336@0)