This topic has been archived. It cannot be replied.
-
枫下家园 / 美丽家居 / 自己动手安装 garage door opener
-dynamite(慢慢找);
2009-6-5
{447}
(#5318116@0)
-
good job. but the picture is small.
-qwertyasd(东北人-努力工作争取);
2009-6-5
(#5318126@0)
-
Piece of cake, right?
-richxie(土豆);
2009-6-5
(#5318127@0)
-
也不能说one piece of cake, 大概 three pieces of cake
-dynamite(慢慢找);
2009-6-5
(#5318255@0)
-
照片在此
-dynamite(慢慢找);
2009-6-5
{981}
(#5318164@0)
-
从照片看,车库门上端缺少一个结实的金属横梁,时间长了会把门的中间部分拉变形。我一个朋友的门和上框之间被拉分开了三寸宽的缝,他只用了半年门就废掉了。
-richxie(土豆);
2009-6-5
(#5318307@0)
-
agreed
-cl281(担担面&蛋炒饭);
2009-6-5
(#5318372@0)
-
don't think the frame will bent, more likely the door itself. Your friends door simply too poor quality. The stud behind wall is more than sufficient to suppor the little force to move the door.
-hr1551(hr1551);
2009-6-5
(#5318461@0)
-
You misunderstood. I said the door bent.
-richxie(土豆);
2009-6-5
(#5318883@0)
-
请教懂行的朋友, 我的电动门是一个朋友帮忙装的,可声音特别的大,不知道问题出在哪里,我都觉得有些扰民了。
-freebird_gao(freebird);
2009-6-6
(#5320009@0)
-
请你那个朋友来家吃吨rice, 顺便请他处理一下噪音大的问题, 注意要先解决问题后eat rice.
-sharkbait(nemo);
2009-6-6
(#5320190@0)
-
"吃吨rice"?这几吨rice下去,别的问题就出来了。
-bigjoe(万里独行);
2009-6-6
(#5320672@0)
-
所以要先解决问题再吃啊.
-sharkbait(nemo);
2009-6-7
(#5321024@0)
-
门不会被拉变形
-dynamite(慢慢找);
2009-6-5
{565}
(#5318895@0)
-
图在这里
-dynamite(慢慢找);
2009-6-5
{157}
(#5318917@0)
-
Hope the horizontal L-shaped steel beam between the two pieces of wood will be strong enough. Wish you good luck.
-richxie(土豆);
2009-6-6
(#5320551@0)
-
你每次开关时, 机器是否稳定? 我家的垂直悬挂的两根铁条跟你的一样, 我发现它们似乎单薄了点, 每次开关时, 机器都有晃动.
-monte_cristo(基度山伯爵);
2009-6-6
(#5320795@0)
-
机器比较稳定,只是刚启动的时候颤一下。HD的人是推荐买两根好的角钢,就是我买的钉在天花板上的那种,刚度大多了。package里的角钢的确显得刚度不够。但相信制造商,而且买两根好的角钢又要花20多块。所以仍旧用package里的角钢。用裁下的好角钢余料做了斜撑,增加稳定。
你的机器不稳定,是不是轨道和机器没有垂直?所以启动时让它左右晃动。如果不是,多加点斜撑应该有用。
-dynamite(慢慢找);
2009-6-7
{314}
(#5321547@0)